GES 401, Insertion probe, Pt100
Measuring range: -50...+400 °C
Response time: t90 = ca. 10 sec.



Technical data: non-corrosive and acid-resistant V4A tube, plastic handle, ca. 1m PVC cable, anti-kink connection, 4-pin Mini-DIN-plug with needle-type prod
Suitable for: GMH 2000, GMH 2000 SA, GMH 3530, GMH 3710, GMH 3750

 

 

GES 175, Insertion probe
Measuring range: -70...+200 °C
Response time: t90 = ca. 10 sec.



Suitable for: GMH 175, GFTH 200, GIM 1840 - ST60, GIM 1840 - ST80

 

 

GES 175 LE, Insertion probe, loose ends
Measuring range: -70...+200 °C
Response time: t90 = ca. 10 sec.

 

 

GES 900
Measuring range:   -65 ... +1000 °C
Response time:        t90 = ca. 5 sec.



Technical details:   V4A tube (D = 3,0 mm) elastic (rigid), plastic handle, spiral cable , DIN-plug

 

 

GES 130, Insertion probe, type K
Measuring range: -65...+550 °C
Response time: t90 = ca. 5 sec.



Technical details: Flexible V4A insertion needle, plastic handle, spiral cable , DIN-plug

 

 

GES 500, Insertion probe
Measuring range: -65...+550 °C
Response time: t90 = ca. 5 sec.




Technical details: Flexible V4A insertion needle, plastic handle, spiral cable , DIN-plug

 

 

GES 401, Insertion probe, Pt100
Measuring range: -50...+400 °C
Response time: t90 = ca. 10 sec.



Technical data: non-corrosive and acid-resistant V4A tube, plastic handle, ca. 1m PVC cable, anti-kink connection, 4-pin Mini-DIN-plug with needle-type prod
Suitable for: GMH 2000, GMH 2000 SA, GMH 3530, GMH 3710, GMH 3750

 

 

GES 38
Technical Specification:

Measuring range:	-50°C ... +200°C
Probe:	diameter 4mm, length 150mm, V4A
Cable:	1m silicon cable
for use with:	GMH 3830, GMH 3850 - unsuitable for GMH 3810 !
usage:	for temperature measurement of e.g. wood chips, etc.

 

 

GES 21K

• -50 ... +250 °C

big white teflon handle water- and steam-tight, stainless steal anti-buckling, 1 m teflon calbe, DIN plug, teflon handle
Use for canteen kitchen, backeries, butcher´s shops, etc.

 

 

GES 20K

• -65 ... +550 °C

V4A tube with Ø 1.5 mm slim insertion tip, small teflon handle, stainless steel kink protection, 1 m teflon cable, miniature flat plug

Response time T₉₀: approx. 3 s
Use for: canteen kitchen, backeries, butcher´s shops, etc.

 

 

GMH 3350
Measuring Ranges: 
Humidity:   0,0 ... 100,0 % r.h.
Ambient Temperature:   -40 ... +120 °C
Surface Temperature:   -80,0 ... +250,0 °C
Dew Point Temperature:   -40,0 ... +70,0 °C
Dew Point Distance:   -200,0 ... +290,0 °C
Enthalpy:   0 ... 250 kJ/kg
Flow Rate:   depending on STS probe

Accuracy (only device):
Rel. Humidity:    ± 0,1%
Ambient Temperature (Pt1000):   ± 0,2%
Surface Temperature (NiCr-Ni):   ± 0,5% of reading ± 0,5 °C
Flow Rate:   ± 0,1%

Measured Data Storage:  99 (manual), 5400 (cyclic)
Cycle Time:   1sec. ... 1h
Alarm:   visual and acustical via integrated buzzer

Miscellaneous:       Serial Interface, Ready for Bus Operation, Min./Max. Value Memory,
                                   Hold Function, Real-Time Clock, Battery-/Mains operation

Suitable Probes:   TFS 0100 E, STS 005, STS 020, all temperature probes type K with plug
                                 ( no probe included, please order separately )

 

 

GNG 12/24   (24VDC/80mA)
Input: 10...18VDC
Output: 24VDC ±5%, max. 80mA
Feature: For electrical isolation of 12VDC power supply voltages

 

 

GNG 24/24   (24VDC/80mA)
Input: 19...30VDC
Output: 24VDC ±5%, max. 80mA
Feature: For electrical isolation of 24 V DC power supply voltages

 

 

GNG 12/2x24   (2x24VDC/80mA)
Input: 10...18VDC
Output: 2 x 24VDC ±5%, each max. 80mA
Feature: For electrical isolation of 12 V DC power supply voltages

 

 

GNG 24/2x24   (2x24VDC/80mA)
Input: 19...30VDC
Output: 2 x 24VDC ±5%, each max. 80mA
Feature: For electrical isolation of 24 V DC power supply voltages

 

 

GITT01, Universal Transmitter
Input signal:

• Resistance thermometer:   Pt100, Pt500, Pt1000, Ni500, Ni1000
• Thermocouples:   B, C, D, E, J, K, L, N, R, S, T, U
• Resistance-type sensor:   10...400 Ohm, 0...2000 Ohm
• Voltage sensor:   -10...+100 mV
  
  Output signal:   4-20 mA or 20-4 mA
  Features:   electrically isolated, freely programmable via programming tool

Please order article separately per email.
State input signal and measuring range when ordering.

 

 

GITT01 - Ex, universal transmitter
Input signal:

• Resistance thermometer:   Pt100, Pt500, Pt1000, Ni500, Ni1000
• Thermocouples:   B, C, D, E, J, K, L, N, R, S, T, U
• Resistance-type sensor:   10...400 Ohm, 0...2000 Ohm
• Voltage sensor:   -10...+100 mV
  
  Output signal:   4-20 mA or 20-4 mA
  Explosion-protection approval:   ATEX II G EEx ia IIC T4/T5/T6
  Features:   electrically isolated, freely programmable via programming tool
  
  
  

  Please order article separately per email.
  State input signal and measuring range when ordering.

 

 

GBS 01
Measuring ranges: 0.1 (1m) / 0.25 / 0.4 / 0.5 / 0.6 / 1 / 1.6 / 2.5 / 4 / 6 / 10 / 16 / 25bar (250m)
Output signal: 4...20 mA (others upon request)
Electric connection: 10m PUR-cable, stationary casted (longer cable upon request)
Working temperature: -10...+60 °C
Uses: water resp. non-aggressive liquids
Application: level indication, level regulation

 

 

GBS 02
Measuring ranges: 0.1 (1m) / 0.25 / 0.4 / 0.5 / 0.6 / 1 / 1.6 / 2.5 / 4 / 6 / 10 / 16 / 25bar (25m)
Output signal: 4...20 mA (others upon request)
Electric connection: 10m FEP-cable, stationary casted (longer cable upon request)
Working temperature: -10...+85 °C
Uses: fuel oil, diesel and aggressive mediaUses: water resp. non-aggressive liquids
Application: level indication, level regulation

 

 

S-10 REL
Measuring ranges: 0.1 / 0.16 / 0.25 / 0.4 / 0.6 / 1 / 1.6 / 2.5 / 4 / 6 / 10 / 16 / 25 / 40 / 60 / 100 / 160 / 250 / 400 / 600 / 1000
Output signal: 4...20 mA (standard), 0...10 V
Pressure connection: G 1/2A
Electric connection: angle connector according to DIN 43650

 

 

S-11 REL
Measuring Ranges:

• 0.1 / 0.16 / 0.25 / 0.4 / 0.6 / 1 / 1.6 / 2.5 / 4 / 6 / 10 / 16
• 25 / 40 / 60 / 100 / 160 / 250 / 400 / 600 / 1000

Output signal: 4...20 mA (standard), 0...10 V
Power Supply:   10...30VDC (14...30VDC at output 0-10V)
Pressure connection: G1A (up to 2.5 bar), G 1/2A (4...16 bar)
Electric connection: angle connector according to DIN 43650

 

 

GTF 101 Pt100
Measuring Range: -50...+400 °C (Standard) or -200...+600 °C (mineral-insulated tube)



Sensor: Pt100, isolated (Pt1000 on request)
Accuracy: DIN class B (Standard), 1/3DIN, 1/10DIN
Material (Tube): V4A
Probe Length FL: 100mm (standard) or custom-made
Diameter D: 1.6mm, 2.2mm, 3mm (standard), 4mm, 5mm, 6mm or 8mm
Cable Length KL: 1m silicone (standard) or custom-made
Number of Wires: 2-wire, 3-wire or 4-wire (standard)
Cable Jacket: PVC (70 °C), Silicone (200 °C), Teflon (250 °C), Glas silk (400 °C)
Cable Sleeve KH: 50mm x 5mm

Note: Depending on the wanted versions, there can be surcharges

Ordering Example: GTF 101 Pt100, -50/+200 °C, 4-wire, FL=100mm, D=3mm, KL=1m Silicone

 

 

GTF 101 NiCr-Ni, Temperature Probe
Measuring Range: -50...+200 °C (Standard) -200 °C...+1150 °C (sheath thermocouple)



Sensor: Typ K (NiCr-Ni), class 1, isolated
Material (Tube): V4A
Probe Length FL: 100mm (Standard) or custom-made
Diameter D: 0.5mm, 1.0mm, 1.5mm, 3mm (Standard), 4mm, 5mm, 6mm or 8mm
Cable Length KL: 1m Silicone (Standard) or custom-made
Cable Jacket: PVC (70 °C), Silicone (200 °C), Teflon (250 °C), Glas silk (400 °C)

Note: There can be surcharges depending on the wanted version

Ordering Example: GTF 101 NiCr-Ni, -50/+200 °C, FL=100mm, D=3mm, KL=1m Silicone

 

 

GTF 102 Pt100, Temperature Probe
Measuring range: -50...+400 °C or -200...+600 °C (with mineral-insulated tube)



Sensor: Pt100, isolated (Pt1000 on request)
Accuracy: DIN class B (Standard), 1/3DIN, 1/10DIN
Material (tube): V4A
Probe Length FL: 100mm (Standard) or custom-made
Extension Length HL: 0mm (Standard) or 50mm (if temp. > 200 °C)
Diameter D: 1.6mm, 3mm (Stand.), 4mm, 5mm, 6mm or 8mm
Thread G:: G1/8", G1/4", G3/8", G1/2" (Stand.), G3/4", M8x1, M10x1 or M14x1.5
Cable Length KL: 1m Silicone (Standard) or custom-made
Number of Wires: 2-, 3-, or 4-wire (Standard)
Cable Jacket: PVC (70 °C), Silicone (200 °C), Teflon (250 °C), Glas Silk (400 °C)
Cable Sleeve KH: 50mm x 5mm

Note: There can be surcharges depending on the wanted version

Ordering example: GTF 102 Pt100, -50/+200 °C, 4-wire,FL=100mm, D=3mm, G1/2", KL=1m Silicone

 

 

GTF 102 NiCr-Ni, Temperature Probe
Measuring Range: -50...+200 °C (Stand.) or -200...+1150 °C (with sheath thermocouple)



Sensor: Type K (NiCr-Ni), class 1, isolated
Material (Tube): V4A
Probe Length FL: 100mm (Stand.) or custom-made
Extension Lenth HL: 0mm (Stand.) or 50mm (if Temp. > 200 °C)
Diameter D: 0.5mm, 1.0mm, 1.5mm, 3mm (Stand.), 4mm, 5mm, 6mm or 8mm
Thread G:: G1/8", G1/4", G3/8", G1/2" (Stand.), G3/4", M8x1, M10x1 or M14x1.5
Cable Length KL: 1m Silicone (Standard) or custom-made
Cable Jacket: PVC (70 °C), Silicone (200 °C), Teflon (250 °C), Glas Silk (400 °C)
Cable Sleeve: 50mm x 5mm

Note: There can be surcharges depending on the wanted version

Ordering example: GTF 102 NiCr-Ni, 0/+800 °C, FL=100mm, HL=50mm, D=3mm, G1/2", KL=1m Silicone

 

 

ALSCHU 480 P

• Alarm in case of any liquid leaking or penetrating
• External solenoid valves can be closed
• Connection of water probes, liquid level switch, safety mat etc. possible
• Volt-free switching output
  
  Technical data:
  Power supply: 230V, 50/60 Hz
  Power consumption: ca. 1Watt
  Control output: volt-free, for AC and DC voltages up to max. 230V AC
  Switching capacity: ca. 2400 VA
  Sensor connection: 2.5mm jack connector

 

 

GTP
Measuring range: max. -200...+800 °C
Standard measuring ranges: 0...100 °C, 0...200 °C, -50...+50 °C, -50...+150 °C
Output signal: 4...20mA, 0-10V (option)
Sensor connection: Pt100 (2- or 3-wire)
Dimensions: 56.5 x 73 x 20mm

Options - Surcharges:
-AV010: output voltage 0-10V
-AV...: other output voltage
-MB: any other measuring range
-LACK: card coated on both sides

 

 

GTP-SG
Measuring range: max. -200...+800 °C
Standard measuring ranges: 0...100 °C, 0...200 °C, -50...+50 °C, -50...+150 °C
Output signal: 4...20mA, 0-10V (option)
Sensor connection: Pt100 (2- or 3-wire)
Dimensions: 56.5 x 73 x 20mm

Options - Surcharges:
-AV010: output voltage 0-10V
-AV...: other output voltage
-MB: any other measuring range
-LACK: card coated on both sides

 

 

GNTP
Measuring range: max. -200...+1200 °C
Standard measuring ranges: 0...100 °C, 0...600 °C, 0...1200 °C, -50...+150 °C, -200...+300 °C
Output signal: 4...20mA, 0-10V (option)
Sensor connection: NiCr-Ni (type K), according to DIN IEC 584

Options - Surcharges:
-AV010: output voltage 0-10V
-AV...: other output voltage
-MB: any other measuring range
-LACK: card coated on both sides
-SSK: screw type / plug-in terminals

 

 

GNTP-SG
Measuring range: max. -200...+1200 °C
Standard measuring ranges: 0...100 °C, 0...600 °C, 0...1200 °C, -50...+150 °C, -200...+300 °C
Output signal: 4...20mA, 0-10V (option)
Sensor connection: NiCr-Ni (type K), according to DIN IEC 584

Options - Surcharges:
-AV010: output voltage 0-10V
-AV...: other output voltage
-MB: any other measuring range
-LACK: card coated on both sides
-SSK: screw type / plug-in terminals

 

 

GTMU, design type 1, Pt100
Measuring range: max. -200...+800 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, 0...200 °C, -50...+50 °C, -50...+150 °C (without surcharge)
Probe: Pt100 class B, length=100mm, D=6mm, G=1/2" (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: with screwed end "G" for direct screw connection

 

 

GTMU, design type 2, Pt100
Measuring range: max. -200...+800 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, 0...200 °C, -50...+50 °C, -50...+150 °C (without surcharge)
Probe: Pt100 class B, length of collar tube=50mm, length=100mm, D=6mm, G=1/2" (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: screwed end "G" at distance from housing, for extra high temperatures

 

 

GTMU, design type 3, Pt100
Measuring range: max. -200...+800 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, 0...200 °C, -50...+50 °C, -50...+150 °C (without surcharge)
Probe: Pt100 class B, length=50mm, D=3mm, (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: direct surface mounting with permanently connected probe

 

 

GTMU, design type 4, Pt100
Measuring range: max. -200...+800 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, 0...200 °C, -50...+50 °C, -50...+150 °C (without surcharge)
Probe: Pt100 class B, length=100mm, D=6mm, (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: sensor tube arrangement: centrally mounted and vertically down

 

 

GTMU, design type 5, Pt100
Measuring range: max. -200...+800 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, 0...200 °C, -50...+50 °C, -50...+150 °C (without surcharge)
Probe: no probe included, please order separately
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: screw connection M12 for mounting of sensors already existing on site

 

 

GTMU, design type 1, NiCr-Ni
Measuring range: max. -200...+1372 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, -50...+150 °C, -200...+300 °C, 0...600 °C, 0...1200 °C (without surcharge)
Probe: NiCr-Ni class 1, length=100mm, D=6mm, G=1/2" (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: with screwed end "G" for direct screw connection

 

 

GTMU, design type 2, NiCr-Ni
Measuring range: max. -200...+1372 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, -50...+150 °C, -200...+300 °C, 0...600 °C, 0...1200 °C (without surcharge)
Probe: NiCr-Ni class 1, length of collar tube=50mm, length=100mm, D=6mm, G=1/2" (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: screwed end "G" at distance from housing, for extra high temperatures

 

 

GTMU, design type 3, NiCr-Ni
Measuring range: max. -200...+1372 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, -50...+150 °C, -200...+300 °C, 0...600 °C, 0...1200 °C (without surcharge)
Probe: NiCr-Ni class 1, length=50mm, D=3mm, (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: direct surface mounting with permanently connected probe

 

 

GTMU, design type 4, NiCr-Ni
Measuring range: max. -200...+1372 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, -50...+150 °C, -200...+300 °C, 0...600 °C, 0...1200 °C (without surcharge)
Probe: NiCr-Ni class 1, length=100mm, D=6mm, (others upon request)
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: sensor tube arrangement: centrally mounted and vertically down

 

 

GTMU, design type 5, NiCr-Ni
Measuring range: max. -200...+1372 °C (please consider the temperature the housing is exposed to)
Standard measuring ranges: 0...100 °C, -50...+150 °C, -200...+300 °C, 0...600 °C, 0...1200 °C (without surcharge)
Probe: no probe included, please order separately
Output signal: 4...20mA (options: 0-1V, 0-2V, 0-5V, 0-10V)
Design type: screw connection M12 for mounting of sensors already existing on site

 

 

GTF 103 Pt100, Temperature Probe

Measuring Range: -50...+400 °C or -200 ...+600 °C (with insulated sheath tube)



Sensor: Pt100 DIN class B, isolated (Pt1000 on request)
Tube material: V4A
Probe length FL: 100mm (stand.) or custom-made
Extension length HL: 0mm (stand.) or 50mm (for temp. > 400 °C)
Diameter D: 6mm (standard) or 0.5mm, 1.0mm, 1.5mm, 3mm, 4mm, 5mm, or 8mm
Thread G:: G1/2" (stand.) or without thread
Connection head: DIN B-head (aluminium) wth terminal socket
Special design: with output signal 4-20mA

Note: Depending on the wanted version, there can be surcharges

Ordering example: GTF 103 NiCr-Ni, 0/+800 °C, FL=100mm, HL=50mm, D=6mm, G1/2"

 

 

GTF 103 NiCr-Ni
Measuring Range: -50...+400 °C or -200 ...+1150 °C (with sheath thermocouple)



Sensor: Type K (NiCr-Ni), class 1, isolated
Tube material: V4A
Probe length FL: 100mm (stand.) or custom-made
Extension length HL: 0mm (stand.) or 50mm (for temp. > 400 °C)
Diameter D: 6mm (standard) or 0.5mm, 1.0mm, 1.5mm, 3mm, 4mm, 5mm, or 8mm
Thread G:: G1/2" (stand.) or without thread
Connection head: DIN B-head (aluminium) wth terminal socket
Special design: with output signal 4-20mA

Note: Depending on the wanted version, there can be surcharges

Ordering example: GTF 103 NiCr-Ni, 0/+800 °C, FL=100mm, HL=50mm, D=6mm, G1/2"

 

 

GFTH 200 SET incl. GIM 530 MS

• Very easy locating of heat and cold bridges
• Laser sighting to aim at the measurement object
• Audible warning at dew point undershooting
• Fast detection of problematic areas tending to mold infestation
  
  Technical data: Hygro-/Thermometer GFTH 200
  Measuring range (temperature): -25.0...+70.0 °C
  Measuring range (humidity): 0,0 ... 100,0 %r.h.
  Resolution: 0,1 %r.h. and 0,1 °C / 0,1 °F
  Features: Min-/Max-reading, Hold function, Socket for external temperature probe
  
  Technical data: IR-Thermometer GIM 530MS
  Temperature Range: -32...+530 °C (-20...+980 °F)
  Resolution: 0,1 °C (0,1 °F)
  Response Time: 0,3 sec. (95%)
  Accuracy: +/- 1% or +/- 1 °C
  Emissivity: 0,100 ... 1,000, adjustable
  Optical Resolution D/S: 20:1
  Dimensions, Weight: 190 x 38 x 45mm, 150g
  
  Scope of delivery: GFTH 200, GIM 530 MS, case, instruction manual

 

 

GTF101-N03250, type N
Measuring range: -50...+1300 °C (short-term peaks up to ca. 1330 °C)



Technical data: stainless steel tube, 1m silicone cable, loose ends
Mantle material: special steel with extraordinary resistance against oxidation at high temperatures and excellent corrosion resistance in chlorine and ammoniacal environments, protective layer emerges at temperatures above 980 °C

 

 

GTF101-N03500, type N
Measuring range: -50...+1300 °C (short-term peaks up to ca. 1330 °C)



Technical data: stainless steel tube, 1m silicone cable, loose ends
Mantle material: special steel with extraordinary resistance against oxidation at high temperatures and excellent corrosion resistance in chlorine and ammoniacal environments, protective layer emerges at temperatures above 980 °C

 

 

GTF101-N031000, type N
Measuring range: -50...+1300 °C (short-term peaks up to ca. 1330 °C)



Technical data: stainless steel tube, 1m silicone cable, loose ends
Mantle material: special steel with extraordinary resistance against oxidation at high temperatures and excellent corrosion resistance in chlorine and ammoniacal environments, protective layer emerges at temperatures above 980 °C

 

 

OXY 3610 MP, oxygen transmitter
Measuring range (oxygen concentration): 0.00...25.00 mg/l (dissolved)
Measuring range (temperature): 0.0...50.0 °C
Output signal: 4-20 mA
Auxiliary energy: 12...30 V DC
Electrode connection socket: 5-pin jack connector, screwable
Oxygen sensor:

• Electrode: active membrane type, with integrated NTC
• Working pressure: max. 3 bar
• Product life: 3 years or more (depending on maintenance)
• Dimensions: total length 220mm, build in length 110mm
• Cable length: 4m, with 5-pin plug, screwable
  
  Options - Surcharges:
  -AV010: output voltage 0-10V

 

 

OXY 3690 MP, oxygen transmitter
Measuring range (oxygen concentration): 0,0 ... 100,0 % O2 (gaseous)
Measuring range (temperature): -20.0...+50.0 °C
Output signal: 4-20 mA
Auxiliary energy: 12...30 V DC
Electrode connection socket: 5-pin jack connector, screwable
Oxygen sensor:

• Sensor element: exchangeable, suitable for high CO2 concentrations
• Working pressure: 500...2000 hPa (static)
• Product life: 18 month warranty on sensor element
• Cable length: 1.3m, with 5-pin plug, screwable
  
  Options - Surcharges:
  -AV010: output voltage 0-10V
  -GOO: open sensor type, suitable for air stream

 

 

EB 3000

• max. 20 sensor modules can be connected via one single line
• no additional voltage supply required
• 5 relay outputs
• Regulating functions can be assigned to any channel
• 2 channels for calculating functions (average value, difference, etc.)
  
  Input:    max. 20 sensor modules
  Maximum allowable cable length:    500m
  Interface:    EASYBUS
  Display:    4 - digit LED (measured value), 2 - digit LED (channel)
  Switching outputs:    4 normally open contacts
  Alarm output:    1
  Interface:    Easybus
  Dimensions:    48 x 96 x 100 mm
  Power supply:    230 V AC, 50/60 Hz
  
  Miscellaneous:    min./max. value memory, calculating functions, etc.
  
  Note:
  For configuration of the EB 3000 and recording / reading-out of connected EASYBUS modules respectively, the serial converter EBW 1 will be required

> Accessory (2)     

 

GTF 401 1/3 DIN, Immersion probe, Pt100

• -50...+400 °C          t90 = approx. 10 sec.          1/3 DIN Cl.B
  
  
  
  
  Technical Details:
  
  Sensor:           Pt100, 1/3 DIN Class B *
  General:          non-corrosive and acid-resistant V4A tube, plastic handle, ca. 1m PVC cable, 
                            anti-kink connection, 4-pin Mini-DIN-plug
  
  Suitable for:   GMH 3530, GMH 3710, GMH 3750
  
  * The senosor accuracy of 1/3DIN is only valid for the measuring range 0...150°C. In the ranges -50...0°C and
  150...300°C, the sensor accuracy is 1/2 DIN. The remaining measuring range has an accuracy of DIN Cl.B.

 

 

GTF 401 1/10 DIN, Immersion probe, Pt100

• -50...+400 °C          t90 = approx. 10 sec.          1/10 DIN Cl.B
  
  
  
  
  Technical Details:
  
  Sensor:           Pt100, 1/10 DIN Class B *
  General:          non-corrosive and acid-resistant V4A tube, plastic handle, ca. 1m PVC cable, 
                            anti-kink connection, 4-pin Mini-DIN-plug
  
  Suitable for:   GMH 3530, GMH 3710, GMH 3750
  
  * The senosor accuracy of 1/10DIN is only valid for the measuring range 0...100°C. In the ranges -50...0°C and
  100...300°C, the sensor accuracy is 1/3 DIN. The remaining measuring range has an accuracy of 1/2 DIN.

 

 

EBT - IF1
Technical Details:

Measuring Range:       -30,0 ... +100,0 °C, other ranges on request
Measuring Sensor:      internal Pt1000 sensor
Accuracy Electronic:   ±  0,2% of reading ± 0,2°C
Accuracy Sensor:   DIN class B (higher accuracy possible)
Serial Interface:       EASYBUS
Working Temperature:   -25 till 70°C

Cable Sleeve:        Ø15 x 35mm (without screwing)
Probe Length:       FL = 100mm (other on customer requirement)
Probe Diameter:   D=6mm  (Standard), 
                                  possible Ø:  4, 5, 6 und 8mm

Special Features:   min- / max- value memory
Calibration:   zero and scale via serial interface adjustable

 

 

EBT - IF2
Technical Details:

Measuring Range:       -30,0 ... +100,0 °C, other ranges on request
Measuring Sensor:      internal Pt1000 sensor
Accuracy Electronic:   ±  0,2% of reading ± 0,2°C
Accuracy Sensor:   DIN class B (higher accuracy possible)
Serial Interface:       EASYBUS
Working Temperature:   -25 till 70°C

Cable Sleeve:          Ø15 x 35mm (without screwing)
Probe Length:         FL = 100mm (other on customer requirement)
Thread:                     G1/2" (Standard)
                                   possible threads: M8x1, M10x1, M14x1.5, G1/8", G3/8", G3/4"
Probe Diameter:    D=6mm  (Standard), 
                                   possible Ø:  4, 5, 6 und 8mm

Special Features:   min- / max- value memory
Calibration:   zero and scale via serial interface adjustable

 

 

EBT - IF3
Technical Details:

Measuring Range:       -70,0 ... +400,0 °C, other ranges on request
Measuring Sensor:      internal Pt1000 sensor
Accuracy Electronic:   ±  0,2% of reading ± 0,2°C
Accuracy Sensor:   DIN class B (higher accuracy possible)
Serial Interface:       EASYBUS
Working Temperature:   -25 till 70°C

Cable Sleeve:          Ø15 x 35mm (without screwing)
Probe Length:         FL = 100mm (other on customer requirement)
Extension Length:  HL = 100mm (Standard), other on customer requirement
Thread:                     G1/2" (Standard)
                                   possible threads: M8x1, M10x1, M14x1.5, G1/8", G3/8", G3/4"
Probe Diameter:    D=6mm  (Standard), 
                                   possible Ø:  4, 5, 6 und 8mm

Special Features:   min- / max- value memory
Calibration:   zero and scale via serial interface adjustable

 

 

GTMU - IF1
Measuring Range:       -30,0 ... +100,0°C (Standard), others on request
                                          The probe length has to be choosen long enough, that the allowable 
                                          temperature range of the electronics, located in the cable sleeve, is not
                                          exceeded.

Sensor:                            internal Pt1000 sensor
Accuracy Electronic:   ±0,2% of reading ±0,2°C
Accuracy Sensor:         DIN class B
Output Signal:                4...20mA, 2 wire
Auxiliary Power:            10 ... 30VDC
Working Temperature Electronic:  -25 ... +60°C
Housing:                          stainless steel

Cable Sleeve:          Ø15 x 35mm (without screwing)
Probe Length:         FL = 100mm (other on customer requirement)
Probe Diameter:    D=6mm  (Standard), 
                                   possible Ø:  4, 5, 6 und 8mm

Scaling:   The transmitter can be scaled freely within the measuring ranges via
                  GTMU-IF programming tool

 > Options (1) 

 

GTMU - IF2
Measuring Range:       -30,0 ... +100,0°C (Standard), others on request
                                          The probe length has to be choosen long enough, that the allowable 
                                          temperature range of the electronics, located in the cable sleeve, is not
                                          exceeded.

Sensor:                            internal Pt1000 sensor
Accuracy Electronic:   ±0,2% of reading ±0,2°C
Accuracy Sensor:         DIN class B
Output Signal:                4...20mA, 2 wire
Auxiliary Power:            10 ... 30VDC
Working Temperature Electronic:  -25 ... +60°C
Housing:                          stainless steel

Cable Sleeve:          Ø15 x 35mm (without screwing)
Probe Length:         FL = 100mm (other on customer requirement)
Thread:                     G1/2" (Standard)
                                   possible threads: M8x1, M10x1, M14x1.5, G1/8", G3/8", G3/4"
Probe Diameter:    D=6mm  (Standard), 
                                   possible Ø:  4, 5, 6 und 8mm

Scaling:   The transmitter can be scaled freely within the measuring ranges via
                  GTMU-IF programming tool

 > Options (1) 

 

GTMU - IF3
Measuring Range:       -70,0 ... +400,0°C (Standard), others on request
                                          The probe length has to be choosen long enough, that the allowable 
                                          temperature range of the electronics, located in the cable sleeve, is not
                                          exceeded.

Sensor:                            internal Pt1000 sensor
Accuracy Electronic:   ±0,2% of reading ±0,2°C
Accuracy Sensor:         DIN class B
Output Signal:                4...20mA, 2 wire
Auxiliary Power:            10 ... 30VDC
Working Temperature Electronic:  -25 ... +60°C
Housing:                          stainless steel

Cable Sleeve:          Ø15 x 35mm (without screwing)
Probe Length:         FL = 100mm (other on customer requirement)
Extension Length:  HL = 100mm (Standard), other on customer requirement
Thread:                     G1/2" (Standard)
                                   possible threads: M8x1, M10x1, M14x1.5, G1/8", G3/8", G3/4"
Probe Diameter:    D=6mm  (Standard), 
                                   possible Ø:  4, 5, 6 und 8mm

Scaling:   The transmitter can be scaled freely within the measuring ranges via
                  GTMU-IF programming tool

 > Options (1) 

 

EB 3000 FTR

Low-priced monitoring and controlling of temperature and humidity. With a single 2-wire twisted pair cable(e.g. bell wire) the humidity- / temperature sensor EBHT-1R will be connected with the EB 3000. The maximum allowable distance between sensor and controlling device amounts to 500m.

Range of application:

• Refrigeration warehouse, green house, storage room, mature room etc.
  
  Advantages:
• Simple installation by means of polarity free 2-wire system
• 4 switching outputs (humidify, dehumidify, heating, cooling) and 1 alarm output
• Easy retrofitting of up to 20 single sensors (temperature, humidity, standard signals etc.)
• Excellent cost-performance-ratio
  
  
  Technical Details:
  
  Humidity -/Temperature Modul EBHT-1R:
  
  Measuring Range (humidity):     0,0 ... 100,0 %RH
  Recommended Range:     30 ... 80 %RH (standard sensor)
  Recommended Range:     11 ... 90 %RH (high humidity sensor)
  
  Measuring Range (temperature):     -40,0 ... +120,0 °C
  
  Probe length:     50mm
  Output signal:     EASYBus

Display and monitoring device EB 3000:

Input:    max. 20 sensor modules
Maximum allowable cable length:    500m
Interface:    EASYBUS
Display:    4 - digit LED (measured value), 2 - digit LED (channel)
Switching outputs:    4 normally open contacts
Alarm output:    1
Interface:    Easybus
Dimensions:    48 x 96 x 100 mm
Power supply:    230 V AC, 50/60 Hz

Miscellaneous:    min./max. value memory, calculating functions, etc.

Note:
For configuration of the EB 3000 and recording / reading-out of connected EASYBUS modules respectively, the serial converter EBW 1 will be required

Scope of Supply:
1 pcs  EB 3000, monitoring and controlling device
1 pcs  EBHT - 1R, temperature / mumidity modul for on-wall mounting
10m   VSL2P, twisted pair cable, 2 x 0,75²

> Accessory (4)     > Options (1) 

 

GT1-CO
High quality, TÜV certified CO transmitter for detection of carbon monoxide in underground garages, parking garages, boiler plants, heating systems, garages as well as in the ambient air. The CO transducer has a very long-lasting electrochemical  measuring cell and could be easily integrated in existing CO surveillance systems (without loss of validity of existing TÜV certificates). Via two-wire system, displays, controller and alarm devices with 4-20mA input could be connected without any problem.

Range of Application:

• underground garages
• parking garages
• boiler plants
• heating systems
• garages
  
  Highlights:
   
• TÜV certification according to VDI 2053
• also suitable as replacement sensor for existing CO surveillance systems
• long-lasting electrochemical measuring cell
• automatic zero calibration
• scale adjustment possible
  
  
  Technical Details:
  
  Measuring Range:            0 ... 300 ppm
  Measuring Principle:       electrochemical, permanent measuring
  Reproducibility:                 < 3 ppm according to VDI2053
  Response Time:                < 60 s
  Linearity Fault:                   < 2 %  of 300 ppm CO according to VDI2053
  Zero Calibration:               automatically
  Power Supply:                   20 ... 28 VDC
  Dimensions:                       82 x 80 x 55mm (without angle plug), ABS
  Electrical Connection:     Angular Connector according to DIN 43650 (IP65) 

 

 

TF101P-1m
Advantages:

• Highly resilient to chemicals and oils
• Sealed against moisture and corrosion
• Easily cleaned and sterilised
• Food safe
• Small size provides fast response
• Optionally with mechanical protection (V4A-sleeve) and with thread
       or clamping ring screw connection available
• For use in corrosive environments and tight places

Design Type:
Type:                              PFA Pt 100, flexible sealed
Cable length:                1 m
Connection:                  4-wire-connection (4 x 0.14mm² nickel-plated copper)
Nominal diameter:      2.1 mm

Technical Data:
Temperature range:   -60.0 ... +250.0°C  
Accuracy:                      DIN class A

 > Options (1) 

 

TF101P-2m

Advantages:

• Highly resilient to chemicals and oils
• Sealed against moisture and corrosion
• Easily cleaned and sterilised
• Food safe
• Small size provides fast response
• Optionally with mechanical protection (V4A-sleeve) and with thread
       or clamping ring screw connection available
• For use in corrosive environments and tight places
  
  
  
  Design Type:
  Type:                              PFA Pt 100, flexible sealed
  Cable length:                2 m
  Connection:                  4-wire-connection (4 x 0.14mm² nickel-plated copper)
  Nominal diameter:      2.1 mm
  
  Technical Data:
  Temperature range:   -60.0 ... +250.0°C  
  Accuracy:                      DIN class A

 > Options (1) 

 

TF101P-3m

Advantages:

• Highly resilient to chemicals and oils
• Sealed against moisture and corrosion
• Easily cleaned and sterilised
• Food safe
• Small size provides fast response
• Optionally with mechanical protection (V4A-sleeve) and with thread
       or clamping ring screw connection available
• For use in corrosive environments and tight places

Design Type:
Type:                              PFA Pt 100, flexible sealed
Cable length:                3 m
Connection:                  4-wire-connection (4 x 0.14mm² nickel-plated copper)
Nominal diameter:      2.1 mm

Technical Data:
Temperature range:   -60.0 ... +250.0°C  
Accuracy:                      DIN class A

 > Options (1) 

 

TF101K-1m

Advantages:

• Highly resilient to chemicals and oils
• Sealed against moisture and corrosion
• Easily cleaned and sterilised
• Food safe
• Small size provides fast response
• Optionally with mechanical protection (V4A-sleeve) and with thread
       or clamping ring screw connection available
• Also available with thermocouples type J, T and E
• For use in corrosive environments and tight places
  
  
  
  Design Type:
  Type:                             NiCr-Ni (type K), PFA insulated,
                                         provides continuous PFA protection over the measurement junction
  Sensor tip:                   IP 68, hermetically sealed
  Cable length:               1 m
  Junction:                      Electrically-insulate
  Connection:                 Stranded NiCr-Ni thermocouple wire (0.14mm²)
  Nom. cross section:  1.6 x 2.5 mm
  
  Technical Data:
  Temperature range:  -270°C ... +250°C
  Accuracy:                     DIN class A  

 > Options (1) 

 

TF101K-2m

Advantages:

• Highly resilient to chemicals and oils
• Sealed against moisture and corrosion
• Easily cleaned and sterilised
• Food safe
• Small size provides fast response
• Optionally with mechanical protection (V4A-sleeve) and with thread
       or clamping ring screw connection available
• Also available with thermocouples type J, T and E
• For use in corrosive environments and tight places
  
  
  
  Design Type:
  Type:                             NiCr-Ni (type K), PFA insulated,
                                         provides continuous PFA protection over the measurement junction
  Sensor tip:                   IP 68, hermetically sealed
  Cable length:               2 m
  Junction:                      Electrically-insulate
  Connection:                 Stranded NiCr-Ni thermocouple wire (0.14mm²)
  Nom. cross section:  1.6 x 2.5 mm
  
  Technical Data:
  Temperature range:  -270°C ... +250°C
  Accuracy:                     DIN class A  

 > Options (1) 

 

TF101K-3m

Advantages:

• Highly resilient to chemicals and oils
• Sealed against moisture and corrosion
• Easily cleaned and sterilised
• Food safe
• Small size provides fast response
• Optionally with mechanical protection (V4A-sleeve) and with thread
       or clamping ring screw connection available
• Also available with thermocouples type J, T and E
• For use in corrosive environments and tight places
  
  
  
  Design Type:
  Type:                             NiCr-Ni (type K), PFA insulated,
                                         provides continuous PFA protection over the measurement junction
  Sensor tip:                   IP 68, hermetically sealed
  Cable length:               3 m
  Junction:                      Electrically-insulate
  Connection:                 Stranded NiCr-Ni thermocouple wire (0.14mm²)
  Nom. cross section:  1.6 x 2.5 mm
  
  Technical Data:
  Temperature range:  -270°C ... +250°C
  Accuracy:                     DIN class A  

 > Options (1) 

 

EASYLOG 80CL

Double display (e.g. temperature and humidity) Various additional measurement categories available Up to 64 recording sequences
Measurement Range                Temperature:                Humidity:                Pressure:	-25,0 ... + 60°C 0,0 ... 100,0 %r.F. 300,0 ... 1100,0 hPa
Resolution:	0,1°C / 0,1% r.F. / 0,1 hPa bzw. 1 Digit (display and storage)
Additional display ranges:    Wet bulb temperature:     Dewpoint temperature:    Enthalpy:    Atmospheric humidity:    Absolute humidity:	FK:  -27,0 …  +60,0 °C TP:  -40,0 …  +60,0 °C EP:  -25,0 …  +999,9 kJ/kg FG:     0,0 …  +640,0 g/kg ABS:   0,0 ... +200,0 g/cm³
Accuracy                Temperature:                Humidity:                Pressure:	±0,3°C ± 0,017 x (T-25°C) ±2% r.F.,  in the range 10...90% r.F. ±1,0 hPa (typ.) @ 0-60°C
Storage Capacity:	200.000 measurement values (for temperature, humidity and air pressure
Recording Interval:	2 sec. to 5h
Recording Period:	5,7 years @ recording interval of 15 minutes
Working Temperature :	-25 ... +60°C
Interface:	serial, 3-pin miniatur plug
Battery:	1x Lithium Battery, 3.6V
Battery Lifer:	approx. 5 years @ recording interval of 15 minutes
Dimensions Housing:	48,5 mm x 48,5 mm x 35,5 mm (L X W x H)
Included in Delivery:	1 device incl. battery, 1 operating manual
General Information:

The EASYLOG 80CL can be configured, started and stopped by it's buttons. lt is possible to record max. 64 recording sequences (=start/stop processes) with max. 200.000 data sets (humidity/temperature/air pressure). The device additionally supports the display of various units, which are relevant for the air conditioning technology: wet bulb temperature, dew point temperature, enthalpy. and atmospheric humidity.

To use the data logger, the following equipment will be needed additionally:

Serial Converter, e.g. EBW 1 or EBW 3 Software GSOFT 40K (from Version v7.15)

> Accessory (2)     > Options (1) 

 

EBB 2 OUT / BP

Functional description:
The software EasyControl resp. the alarm module EBUW 232 A enquires the EasyBus and therewith all connected sensor modules for occurring alarm conditions. When a value falls below/above a alarm limit, this is signaled to the alarm module EBB 2 OUT, which switches the relevant relays.

Advantages:

• Placing at any point in the EasyBus
• Separate accumulative relays for min.alram, max.alarm and system alarm
• No auxiliary power supply necessary

Technical Data:
Power supply:               via EasyBus
Relays:                            2 changeover relays (volt-free)
Switching raction:        < 1 second
Switching power:         250 V AC / 16A
Triggering:                      via EBUW 232 A or software EasyControl
Easybus connection:   terminal screw, 2-pin, protected against polarity reversal

 

 

EBG-CO2-1R
Advantages:

• Excellent long-term stability
• Auto-calibrating procedure
• Surveillance of the recommended  
• Optical alarm
• Input of offset and scale for adjusting
• Surveillance of the recommended CO₂ concentration in ambient air

Technical Data:

Measuring range:         0 … 2000 ppm CO₂
Measuring principle:    Infrared principle (NDIR)
Accuracy:                       ± 50 ppm / ± 2 % of  meas. value
Auxiliary energy:          12 … 30 V DC, max. 500 mA
Interface:                        EASYBus
Housing:                         82 × 80 × 55 mm (H × W × D)
Weight:                           Ca. 225 g 
                    
Note: 
Connecting an external power supply of 12-36VDC, the EBG - CO2 - 1R could be used as display,
without serial converter EBW1, EB3000 etc.

 

 

GLF 100 RW

High resolution of 0,001 µS/cm 3 conductivity measuring ranges 2,000 / 20,00 / 100,0 µS/cm Display of resistivity Area of Application:     * Checking of pure and ultra-pure water     * Checking of boiler water     * Functional check of ion exchangers     * Measuring of destilled, deionized, demineralized, desalinated water

Measuring Ranges:           Conductivity	0 ... 2,000 µS/cm, 0,00 ... 20,00 µS/cm, 0,0 ... 100,0 µS/cm
Resistivity	0,01 ... 20,00 MOhm * cm
Temperature:	-5,0 ... 80,0 °C, changeable to °F
Accuracy:         Conductivity (typ.)	better ± 1,0% ± 0,5 % FS
Temperature:	± 0,3 K
Temp.kompensation:	OFF:  temperatur compensation deactivated nLF:   non-linear temperature compensation to EN 27888 naCl: compensation for NaCl solutions to EN 60746-3 LIN:   linear temp. compensation with adjustable coefficient
Reference Temperature:	20°C or 25°C, optionally
Working Temperature:	Device: -25 ... +50°C  Electrode:  -5 ... +80°C
Battery:	9V battery, type 6F22 (included in delivery)
Current Consumption:	< 1,5 mA, approx. 200 operating hours
Display:	ca. 11mm high, 4-digit LCD display
Dimensions:	Housing: 110 x 67 x 30 mm (L x W x H)
External Power Supply:	none
Serial Interface:	none
Additional Functions:	BAT, Min-/Max-Value, Auto-Power-Off, Hold, Offset, Scale
Electrode:	Concentric 2-pole stainless steel electrode (1.4404, 1.4435) with integrated temperature sensor Dimensions: Ø12mm, 75mm long, cable length ca. 1m
Included in Delivery:	1 Device with Electrode, 1 Battery, 1 Operating Manual

 

 

GOEL 370

for universal use / for diving applications enhanced life time and more robust against pressure changes for gases with increased CO2 concentrations follow up model for GOEL 369 / S
Measuring Range
Oxygen:	0,0...100,0% O2 (gaseous)
Oxygen Partial Pressure:	0...1100hPa O2
Working Pressure:	0,5...2,0bar abs.
Warranty:	12 month
Advantages:	less dependence on operation position temperatur compensation corrosion protection robust against pressure changes
Scope of Supply:	1 Sensor, 1 Operating Manual

 

 

CaCl
mixing ratio soil: solution is 1:2,5 (volume)
package size: 1 liter

 

 

GMH 5530

Features:

• Waterproof (device and plug connections)
• Serial Interface and analog output
• GLP-features (Good Laboratory Practice)
• Silicone protection cover
• Big dual display
• Background lightning
• Hight resolution (0,001 pH / 0,1 mV)
• incl. calibration protocol

Anwendung:

• Waters measuring, fishkeeping, aquafarming
• Drinking water monitoring, process control, soil measuring
• Food production and monitoring
• Laboratory: Medicine, pharmaceutics, chemistry
• Quality management

Technical Data:

 

 

Measuring ranges:    pH       Redox / mV    Temperature    rH	-2,000 ... 16,000 pH -2000 ... 2000 mV -1000,0 ... 1000,0 mV -5,0 ... 150,0 °C 0,0 ... 70,0 rH
Connections:
pH / Redox	BNC-female connector, compatible to standard BNC-plugs and waterproof BNC-plugs, additional banana-jack (4 mm) for separate reference electrode input resistance: 1012 Ohm
Temperature	2 banana-jacks (4 mm) for temperature probes (Pt1000 or NTC 10K)
Interface /    Supply	4-pole bayonet female connector for serial interface and supply (with accessory USB 5100)
Display:	two 4½-digit 7-segment display (15 mm und 12 mm)

> Accessory (7)     

 

GMH 5550

Features:

• Waterproof (device and plug connections)
• Analog output
• data logger
• Serial Interface and analog output
• GLP-features (Good Laboratory Practice)
• Silicone protection cover
• Big dual display
• Background lightning
• Hight resolution (0,001 pH / 0,1 mV)
• incl. calibration protocol

Anwendung:

• Waters measuring, fishkeeping, aquafarming
• Drinking water monitoring, process control, soil measuring
• Food production and monitoring
• Laboratory: Medicine, pharmaceutics, chemistry
• Quality management

Technical Data:

 

 

Measuring ranges:    pH       Redox / mV    Temperature    rH	-2,000 ... 16,000 pH -2000 ... 2000 mV -1000,0 ... 1000,0 mV -5,0 ... 150,0 °C 0,0 ... 70,0 rH
Connections:
pH / Redox	BNC-female connector, compatible to standard BNC-plugs and waterproof BNC-plugs, additional banana-jack (4 mm) for separate reference electrode input resistance: 1012 Ohm
Temperature	2 banana-jacks (4 mm) for temperature probes (Pt1000 or NTC 10K)
Interface /    Supply	4-pole bayonet female connector for serial interface and supply (with accessory USB 5100)
Display:	two 4½-digit 7-segment display (15 mm und 12 mm)
Analog output	0 - 1 V freely adjustable
Data logger	with measuring point input Recording interval: 1 s ... 1 h Recording period: 416 days at interval 1 h Value memory: cyclic: 10000 data sets                        singular: 1000 data sets
Min-/max-Alarm	Permanent monitoring of alarm boundaries 3 alarm conditions (off, on, no sound)

> Accessory (8)     

 

GW 110 PB

The GW 110PB connects from the EASYBus to the PROFIBUS.

A SPS, PLC, can easily gather measuring values or other data from an EASYBus module. You can connect and talk to any EASYBus module.

Advantages:

Low-cost

• Sensor wiring with cheap 2-pin connection (mixable bus topology)
• No need of separate cabling (4 … 20 mA or 0 … 10 V) to each sensor
• No need of expensive analog input modules

Simple

• Polarity free 2-pin connection
• Mixable bus topology
• Supply (of most EASYBus-modules) directly over the EASYBus

Requirements:

• EASYBus level converter with serial interface (EBW 1, EBW 3, EBW 64)
• Initialized EASYBus-System
• Profibus Master (SPS, PLC or similar)

Scope of Supply:

• Gateway
• Connetion Cable
• Software and Operating Manual

> Accessory (3)     

 

rotaro 3

Rotation speed measuring device via light and reflecting label or measuring tip; velocity and length measurement via measuring wheel

The handheld tachometer rotaro 3 is useful at the installation and setup of plants and machinery as well as for service application, monitoring production processes or use at development laboratory. The rotaro 3 can measure rotary speed of for example motors, turbines, pumps as well as stirring devices, centrifuges and haulage installations,

Specifications:

 

Measuring range
rpm:	optical / mechanical 1 ... 99999 min-1
Velocity:	Ø 1 m: 0,10 ... 1999 m / min
Length:	0 ... 99999 m
Accuracy:	± 0,02 % of m.v. ± 1 Digit
Meas. distance:	optical max. 600 mm / max. 24 inch
LCD:	5-digit LCD display with 10 mm height of digits and floating point at range change, low-battery warning
Functions:	min- / max- value memory, average and last value
Housing:	Material: ABS
	Dimenstions: 175 x 60 x 28 mm
	Weight: 250 g, incl. Batteries

 

 

ecotach

Rotation speed measuring device via light and reflecting label

The handheld tachometer ecotach is useful at the installation and setup of plants and machinery as well as for service application, monitoring production processes or use at development laboratory. The rotaro 3 can measure rotary speed of for example motors, turbines, pumps as well as stirring devices, centrifuges and haulage installations.

Specifications:

 

Measuring range:	1 ... 60.000 rpm
Accuracy:	± 0,02 % of m.w. or ± 1 Digit
Meas. distance:	max. 450 mm / max. 18 inch
LCD:	5-digit LCD display for measuring value with floating point, measuring unit, trigger signal, low-battery warning
Auto Power off:	automatically after 30 s
Housing:	Material: ABS
	Dimensions: 145 x 60 x 28 mm
	Weight: 147 g, incl. Batteries

 

 

GMH 5430

Features:

• Water-proof (device and plug-in connections)
• Serial intervace
• Average filter
• Silicone protection cover
• Large double display
• Background illumination

Application:

• Industry and craft
• Measurements of waters and aquaristics
• Fish farming
• Drinking water monitoring, process control, soil measruements
• Food production and control
• Quality management
• Additional applications at laboratory:
  medicine, pharmacy, chemistry

 

Specification:

 

Number of measuring ranges:	5
Connection:
Electrode	1x 7-pole bayonet socket (Conductivity and Temperature)
Interface /    ext. supply	4-pole socket for serial interface and supply (with accessories: USB adapter USB 5100)
Display:	two 4½-digit 7-segment display (15 mm and 12 mm)

> Accessory (4)     

 

GMH 5450

Features:

• Water-proof (device and plug-in connections)
• Serial intervace
• Analog output
• Data logger
• Average filter
• Silicone protection cover
• Large double display
• Background illumination

Application:

• Industry and craft
• Measurements of waters and aquaristics
• Fish farming
• Drinking water monitoring, process control, soil measruements
• Food production and control
• Quality management
• Additional applications at laboratory:
  medicine, pharmacy, chemistry

 

Specification:

 

Number of measuring ranges:	5
Connection:
Electrode	1x 7-pole bayonet socket (Conductivity and Temperature)
Interface /    ext. supply	4-pole socket for serial interface and supply (with accessories: USB adapter USB 5100)
Display:	two 4½-digit 7-segment display (15 mm and 12 mm)

> Accessory (5)     

 

EBG-CO-1R
Advantages:

• Long-lasting electrochemical measuring cell
• Automatic zero celibration
• 3 years warranty for the CO sensor element
   

Range of Application:

• Underground garages, parking garages
• Boiler plant and heating systems
• Motorcar garage

Technical Data:

Measuring range:                0 … 300 ppm CO
Measuring principle:          electrochemical, permanent measuring
Response Time T90:          < 60 s
Auxiliary energy:                 14 … 30 V DC, max 50 mA
Interface:                               EASYBus
Dimensions Housing:         82 × 80 × 55 mm (L X B x H)
Weight:                                   approx. 20 g 
                    

> Accessory (4)     

 

EBB 2 OUT / 12V

Functional description:
The software EasyControl resp. the alarm module EBUW 232 A enquires the EasyBus and therewith all connected sensor modules for occurring alarm conditions. When a value falls below/above a alarm limit, this is signaled to the alarm module EBB 2 OUT, which switches the relevant relays.

Advantages:

• Placing at any point in the EasyBus
• Separate accumulative relays for min.alram, max.alarm and system alarm
• No auxiliary power supply necessary

Technical Data:
Power supply:               12 V DC ± 10 % / 150 mA
Relays:                            2 changeover relays (volt-free)
Switching raction:        < 0,1 second
Switching power:         250 V AC / 16A
Triggering:                      via EBUW 232 A or software EasyControl
Easybus connection:   terminal screw, 2-pin, protected against polarity reversal

 

 

GMUD MP-S

Microprocessor controlled, digital pressure transducer with display and operation via 3 buttons. With freely scalable analog output that can be switch between 4-20 mA and 0-10 V.

Suitable for: air and non-aggressive gases

Area of application:

• controlling, measuring and monitoring
• climate and ventilation
• environmental and medical technology

Specification:

 

Relative pressure range:	Measuring range
MP-S-MR0	0,0 … 100,0 mbar rel.
MP-S-MR1	0,0 … 500,0 mbar rel.
MP-S-MR2	0 … 1000 mbar rel.
MP-S-MR3	0 … 2000 mbar rel.
MP-S-MR4	0 … 5000 mbar rel.
Absolute pressure range:	Measuring range
MP-S-MA0	0 … 1100 mbar abs.
MP-S-MA1	0 … 2000 mbar abs.
Optimized special ranges possible: see option - MBS (e.g. -350 ... +350 mbar)
Typ. accuracy:	±0,15 % FS (lin.), ±0,6 % FS (hysteresis and temperature 0 ... 70 °C)

 

 

GMUD MP-F

Microprocessor controlled, digital pressure transducer with display and operation via 3 buttons. With freely scalable analog output that can be switch between 4-20 mA and 0-10 V.

Suitable for: air and non-aggressive gases

Area of application:

• controlling, measuring and monitoring
• climate and ventilation
• environmental and medical technology

Specification:

 

Relative fine pressure range:	Measuring range
MP-F-MR0	0,000 … 1,000 mbar rel.
MP-F-MR1	0,00 … 10,00 mbar rel.
MP-F-MR2	0,00 … 20,00 mbar rel.
Optimized special ranges possible: see option - MBF (e.g. -15 ... +15 mbar)
Typ. accuracy:	±0,35 % FS (lin.), ±0,6 % FS (hysteresis and temperature 0 ... 70 °C)

 

 

GFTB 200

Feature:

• air humidity, temperature and air pressure measurement
• additional display for further parameters, e.g. dew point
• temperature and absolute humidity
• alarm function with integrated buzzer
• min / max value memory
• very low power consumption (> 6500 operating hours)
• PC interface

Applications:

• mobile weather station
• housing space, indoor swimming pools
• offi ces and production rooms, laboratories, storage rooms
• museums, gallery, churches
• Cooling and climate technology
• construction, building physics, loss assessment

Measuring ranges:

 

Temperature:	-25.0°C ... +70.0 °C
Air humidity:	0.0 ... 100.0 % r.F. (recommended range: 11 ... 90 % RH)
Air pressure:	10.0 ... 1100.0 mbar
Dew point temperature Td:	-40,0 ... 70,0 °C
Wet bulb temperature Twb:	-27,0 ... 70,0 °C
Moisture content x:	0,0 ... 280,0 g/kg
Absolute humidity d:	0,0 ... 200,0 g/m³

Accuracy:

 

Temperature:	±0,5 % v.MW. ±0,1°C (Pt1000 1/3 DIN B)
Air humidity:	±2,5 % r.F. (at range 11 bis 90%)
Air pressure:	±1,5 mbar (750...1100 mbar)

 

 

Response time:	T90=10sec.
Display:	4½ -digit, approx. 11 mm high LCD-display with additional displays
Power supply:	9V-Batterie Typ IEC 6F22
Current consumption:	max. 20 ?A at 1 meas. / 60 s (mode SLOW) approx. 70 ?A at 1 meas. / 1 s (mode FAST)

 

 

 

GFTB 200 SET incl. Infrarotthermometer GIM 530 MS

• Very easy locating of heat and cold bridges
• Laser sighting to aim at the measurement object
• Audible warning at dew point undershooting
• Fast detection of problematic areas tending to mold infestation
   

Measuring ranges:

 

Temperature:	-25.0°C ... +70.0 °C
Air humidity:	0.0 ... 100.0 % r.F. (recommended range: 11 ... 90 % RH)
Air pressure:	10.0 ... 1100.0 mbar
Dew point temperature Td:	-40,0 ... 70,0 °C
Wet bulb temperature Twb:	-27,0 ... 70,0 °C
Moisture content x:	0,0 ... 280,0 g/kg
Absolute humidity d:	0,0 ... 200,0 g/m³

•  

  Accuracy:

   

  Temperature:	±0,5 % v.MW. ±0,1°C (Pt1000 1/3 DIN B)
  Air humidity:	±2,5 % r.F. (at range 11 bis 90%)
  Air pressure:	±1,5 mbar (750...1100 mbar)

   

   

  Response time:	T90=10sec.
  Display:	4½ -digit, approx. 11 mm high LCD-display with additional displays
  Power supply:	9V-Batterie Typ IEC 6F22
  Current consumption:	max. 20 ?A at 1 meas. / 60 s (mode SLOW) approx. 70 ?A at 1 meas. / 1 s (mode FAST)

  
  
  Technical Details: GIM 530 MS
  Measuring range:   -32C ... +530 °C (-20 °F ... +980 °F)
  Resolution:   0,1 °C (0,1 °F)
  Response Time (t95):   0,3 sec.
  Accuracy   +/- 1% or +/- 1 °C (highest value should be valid)
  Emission rate:   0,100 ... 1,000, adjustable
  Optical resolution D/S:   20:1 (Measuring Distance : Measuring Zone)
  Dimensions, weight:   190 x 38 x 45 mm, 150 g
  
  Scope of supply:   Device with battery, operating manual, device bag made of nylon
   

 

 

TA 888 N

Classic application of the TA 888 N is flow measurement in ventilation ducts. Due to its high resolution of 0.01 m/s even smallest changes of the flow velocity can be easily and fast detected. The sensor´s small dimensions ensure measurements yet in thin tubes and confined spaces. Further applications are function and dirt checks of filters and exhaust ducts as well as measurements of room air velocity.

 

Measuring range Flow:	0.1 ... 25.0 m/s
Measuring range Temperature:	0 ... +50 °C
Accuracy Flow:	0 ... 1 m/s       ±0.25 m/s 1 ... 5 m/s       ±0.5 m/s 5 ... 10 m/s     ±1.0 m/s 10 ... 15 m/s   ±2.0 m/s
Accuracy Temperature:	±1 °C
Display:	LCD display
Dimensions:	210 x 75 x 50 mm (H x W x D)